Low Cost Hosting | Free Web Space | Dedicated Hosting | Windows Hosting | FrontPage Web Hosting | Business Hosting
cheap web hosting
Search the Web

Vacuum Advance System Information

 

Ignition Advance System

Without some way to adjust the ignition for changing rpm or load, the engine wouldn't make much power, and it'd be pretty hard on a gallon of gas.

These are the reasons for the ignition advance system. Three types of ignition advance are used in most street ignition systems;

Static, vacuum and centrifugal. Together, they account for total ignition advance.

The static advance is the ignition timing that's set at the crankshaft. The vacuum and centrifugal advance systems help optimize ignition timing based on

engine load and speed. When the engine's idling, the spark plug must ignite the air/fuel mixture slightly before the piston reaches the top of its stroke.

This ensures the majority of fuel is ignited and will begin to expand when the piston reaches the top of its stroke, pushing the pistons down. This takes

full advantage of the leverage effect of the connecting rod journal on the crankshaft and is known as the static timing. As engine rpm increases,

piston speed goes up. But the burning and expansion rate of the fuel stays the same. To conpensate for this, ignition of the air/fuel mixture needs

to occur earlier so the fuel can begin expanding when the piston is at the top of its stroke. If ignition begins too late, the piston is already moving

down the cylinder and the pressure against the piston generated by the expanding fuel drops. This causes a drop in cylinder pressure with a resulting

decrease in engine torque. On the other hand, if the ignition timing becomes too far advanced, the fuel begins expanding before the piston reaches the top

of its stroke. The pressure caused by the expanding fuel pushes down violently on the piston as it's still moving to the top of the cylinder, causing the hammering

noise that is typical of detonation. It also slows the momentum of the crankshaft, resulting in a loss of power. As you can see, the ignition must advance at a

certain rate to take full advantage of the lerverage effect of the crankshaft and to prevent engine damage. The vacuum advance system is responsible for increasing

ignition advance based on engine load. The lighter the engine load, the greater the advance. The greater the engine load, the less the advance. The vacuum advance

consist of a diaphragm within a metal housing. Connected to one end of the housing is a source of manifold vacuum. On the other end, a plunger is connected to

the diaphragm, wich, in turn, is attached to the distributor breaker plate. When the engine is lightly loaded, such as at idle and when cruising, manifold vacuum is high

and ignigtion timing can be advanced without causing detonation. The high manifold vacuum pulls on the diaphragm. In turn, the diaphragm plunger pulls

on the breaker plate, causing it to rotate. Since the ignition trigger (breaker points, magnetic switch, and so on) is mounted on the breaker plate,

it begins to open earlier, relative to the distributor shaft. And this causes ignition timing to increase.This increase in ignition timing subsdtantially improves

fuel economy. If the engine is accelarated, manifold vacuum drops. This allows the vacuum diaphragm, and in turn, the breaker plate, to ease back

toward their neutral states, reducing ignition timing. Where the vacuum advance system adjusts ignition timing based on engine load, the

centrifugal advance system adjusts timing based on engine speed. The centrifugal advance system consists of two weights positioned at the

top of the distributor shaft. The weights are held to the distributor drive shaft with springs. As engine rpm increases, centrifugal force pulls the weights away from

the distriburtor shaft causing the springs to expand. The weights are connected to the breaker plate assembly. As the weights move outward, they rotate

the breaker plate within the distributor housing, causing the ignition timing to advance. The advance rate is controlled by the mass of the weights and the tension

of the centrifugal weight springs. The vacuum advance system works in concert with the centrifugal advance system in a type of see-saw routine.

Whenenver engine rpm increases, the vacuum advance system allows the ignition timing to ease back. But when engine rpm increases, the

certrifugal advance system increases ignition timing. So they tend to help balance one another. However, two things combine to make this an uneven trade-off.

First, if the centrifugal advance weights and springs are selected for maximum performance, they won't add any more ignition advance above 2500 rpm

or so. Second, the vacuum advance system is more sensitive than the centrifugal advance system; changes in throttle position that may change engine rpm

only slightly and therefore cause no real change in centrifugal advance rate, can cause more significant changes in the vacuum advance system.

Overall, the more ignition timing you can run without causing detonation, the better the performance and fuel economy.

And these are two good reasons for retaining the vacuum advance system for street operation.

Main